BMW X1 E84 facelift sDrive20d, 184 PS, 8-speed automatic, rear-wheel drive (2012–2015)

Research for this car

• Generation guide BMW X1 E84 (2009-2015): known problems and buying guide

  Risky used SUV, because the xDrive transfer case and timing chains can cost a lot. Buy only with full service records.

• Engine guide BMW N47 2.0 diesel (116d to 520d, Mini Cooper D): problems, costs and what to check

  A workable diesel with a costly timing chain weak spot, so buy only with chain proof and check the EGR recall.

• Gearbox guide ZF 8HP 8-speed automatic (BMW Steptronic): problems, costs and what to check

  A solid 8-speed when its fluid is changed on time. Buy with oil records and a clean scan, and avoid one that shudders or has run in limp mode.

Known issues for this car

Before you buy this car

From the generation guide

1. Listen for jerking on the drive and smell the exhaust for diesel. Ask for injector work. Bad result: jerking, a diesel smell or no injector record above 150,000 km.
2. Ask whether the car was mainly used on short trips. Read codes 480A, 4820 and 4821 with a scanner (needs a scanner). Bad result: those codes.
3. At a stop, turn the wheel to full lock both ways and listen for knocks. Look for oil at the rack. Bad result: knocks, play or leaks.
4. Lift the car and check the ball joints, lower-arm mounts and stabiliser links for play. Bad result: play or knocks over bumps.
5. Check every recall in the table by VIN with a BMW dealer. Bad result: an open campaign.

From the engine guide

1. Cold-start rattle (test drive, no scanner). Start the cold engine and listen for a metal rattle at the back of the engine. A rattle that lasts a few seconds is an early warning. Bad: a rattle that stays when warm or under throttle.
2. Chain job invoice (paperwork). Ask for an invoice for a chain job that includes the tensioners and guide rails. Bad: no invoice on a 2007 to 2011 car. Without one, budget 1,500-2,500 EUR (Germany, year not stated), with the gearbox or engine out.
3. Timing fault codes (scanner needed). Read the fault memory. Camshaft timing codes, such as P0016 or P0017, point to a stretched chain. Bad: any camshaft timing code or an engine warning light.
4. EGR recall (check the VIN). Enter the VIN in the KBA or BMW recall check. Recall 14099R covers X3 F25 builds from 2010 to 2014. Bad: an open campaign, or no proof the work was done.
5. Swirl flaps (scanner needed). Read the fault memory for the engine warning light. Bad: the warning light with lost power.
6. Oil history (paperwork). Look for oil changes every 10,000 to 15,000 km with BMW LL-04 oil. Bad: long gaps, or only the 30,000 km Longlife interval.
7. Goodwill (paperwork). Do not count on BMW paying for a chain. Goodwill for chain damage has mostly ended for these builds. Bad: a seller who says BMW will pay.

From the gearbox guide

1. Read the gearbox fault memory with a BMW-capable scanner. Bad result: pressure or solenoid codes such as 4F84, 4F87, P189C or P0748, or a past limp mode.
2. Ask for fluid and filter invoices. Bad result: no fluid change by 80,000 to 120,000 km, or a change without an adaptation reset.
3. Drive the car from cold and select Drive and Reverse. Bad result: a hard 1-2 shift, or a delay of 1-3 seconds before the gear engages.
4. Drive 15 minutes in town, then under load. Bad result: jerky 2-3 shifts, flaring, slipping or a burnt smell.
5. Hold a steady light throttle at low speed. Bad result: a shudder or vibration, which points to the torque converter lock-up clutch.
6. Look under the car on a lift. Bad result: oil at the wiring connector on the case, on the plastic pan or on the cooler lines.

Running costs

ADAC figures for 15,000 km a year over 60 months

ADAC versions