Mercedes-Benz A-Klasse 176 facelift A 200 d, 136 PS, 7-speed dual-clutch, all-wheel drive (2015–2018)

Research for this car

• Generation guide Mercedes-Benz A-Class W176 (2012-2018): known problems and buying guide

  A risky buy unless dry and well serviced. Check the boot and footwells for water, the front suspension for knocks and the recall list by VIN before you pay.

• Engine guide Mercedes OM651 2.1 diesel (C 220 CDI, E 250 CDI, Sprinter): problems, costs and what to check

  Durable when maintained, but check the cold start chain rattle, early injectors and the 2014 tensioner seal before you buy.

• Gearbox guide Mercedes 7G-DCT dual-clutch (724.0): problems, costs and what to check

  Smooth when serviced, but early cars judder and mechatronic or clutch repairs are costly. Buy on oil history and a cold test drive.

Known issues for this car

Before you buy this car

From the generation guide

1. Open the boot and lift the spare-wheel cover. Water, damp carpet or corrosion points to the flap seals behind the rear bumper. Check the footwell and control-unit connectors. A scanner reads stored faults. Bad: water or corrosion.
2. Check rear arches, roof edge, door seams and sills for paint blisters, and the underbody cover edges for rust. Bad: soft bubbles or rust through the paint.
3. Drive over speed bumps and listen for front knocks. Check the drop links (short bars to the anti-roll bar) and the control-arm bushes for play. Bad: clunks or split bushes.
4. Check start-stop at a standstill. If it never works, the buffer battery under the passenger seat may be worn; a scanner reads the fault memory. Bad: no start-stop.
5. Test COMAND or Audio 20 (radio and navigation) with the radio on and off. Pair a phone and select reverse. Bad: a blank camera or a failed map update.

From the engine guide

1. Timing chain (scanner needed). Start the engine cold and listen for a metallic rattle for 1-3 seconds. Ask a Mercedes dealer or a diesel specialist to read the cam phase offset (the timing gap between camshaft and crankshaft) with XENTRY, the Mercedes diagnostic tool. Check for codes P0016 and P0017. A plain OBD2 scanner may miss the offset. Bad: a rattle, a stored P0016 or P0017, or a large offset. A jumped chain can destroy the engine.
2. Coolant (no scanner). Check the coolant level when the engine is cold, and check it again after a few weeks. Ask a dealer whether service action 1204P59A93 was done on the cylinder head coolant connection. Bad: a falling level or no record of the work.
3. Emissions software update (VIN check). Ask a Mercedes dealer to check the VIN for the emissions software update. Bad: no record of the update.
4. Oil and service history (no scanner). Ask for oil change records. Long gaps between oil changes, short trips and poor oil all speed up chain wear. Bad: long gaps or no records.

From the gearbox guide

1. Clutch check (needs a scanner). Start cold, creep and pull away in 1st and 2nd, and hold on a hill. Judder, slip, or a vibration at a standstill with the brake on points to worn clutch plates. Read the clutch touch points (Kisspoint) in XENTRY, Mercedes' diagnostic software; K1 odd gears, K2 even. A value past the threshold means a new clutch.
2. Mechatronic scan (needs a scanner). Read all transmission codes, not just engine codes. A clean scan does not prove health: one 2014 CLA had no codes but still shook and once dropped into neutral. A stored code, a red warning or a limp-home episode means a control unit job.
3. Auxiliary oil pump warning. Ask whether a "Transmission malfunction" message appeared and cleared after gentle driving. A message that stays, or a "stop vehicle" warning, points to the auxiliary pump or control unit. Scan for codes.
4. Cold and warm road test. Drive in stop-go traffic and lift off in 1st and 2nd. Jerking that stays when warm, or shifts that hang under load, points to software, adaptation or clutch wear. Ask for the last software update.
5. Oil and filter records. Ask for invoices for the fluid and both filters, and for the adaptation reset after the last oil change. No record, black oil or metal fuzz on the drain plug means walk away or budget for a service. Dirty oil damages the control unit.

Running costs

ADAC figures for 15,000 km a year over 60 months

ADAC versions